Back to Blog
Flow MeterNovember 18, 20265 min read

Orifice Plate: Sizing, Materials & Standards You Need to Know

An orifice plate is a thin metal disc with a precisely drilled hole. It looks like the simplest part in the plant. Treat it that way, and it bites back with drifting readings and failed audits. This guide covers sizing, materials, and stand

Saeed Lanjekar
Saeed LanjekarAuthor
Orifice Plate: Sizing, Materials   Standards You Need to Know

 

An orifice plate is a thin metal disc with a precisely drilled hole. It looks like the simplest part in the plant. Treat it that way, and it bites back with drifting readings and failed audits.

This guide covers sizing, materials, and standards for EHS buyers, EPC contractors, and plant engineers who want an orifice plate that works from day one.

What Is an Orifice Plate and How Does It Work?

An orifice plate creates a controlled restriction in a pipe, so you can measure flow from the pressure drop. More flow means a bigger drop.

The orifice plate’s working principle takes four steps:

  • Fluid hits the orifice restriction and speeds up.
  • Pressure falls just after the plate.
  • Taps upstream and downstream pick up the pressure difference.
  • A transmitter turns that difference into a flow signal. That is why you often see a flow transmitter orifice plate pair on a datasheet.

Two facts worth keeping. Flow through an orifice plate follows the square root of the pressure difference, so doubling the flow quadruples the drop, says Automation.com. And the ISA Handbook of Measurement Equations and Tables notes that pressure difference across an orifice is used more than any other type of flow measurement.

Which Orifice Plate Type Suits Your Fluid?

Square-edge plates suit clean fluids, while eccentric and segmental plates suit dirty or two-phase flow. Pick by what is actually in your pipe.

  • Square-edge (concentric): clean liquids, gases, and steam. WIKA’s datasheet lists accuracy up to ±0.5% of full-scale flow for its design.
  • Quarter-circle and conical entrance: built for low Reynolds number flows, per Metaval’s product pages.
  • Eccentric: for two-phase, dirty, and particle-laden media, according to WIKA.
  • Segmental: same job as eccentric, usually in larger pipes (WIKA lists sizes above 4 inches).

The trade-off is accuracy. WIKA’s datasheet puts eccentric, segmental, and quarter-circle designs at up to ±2% of full scale.

How Do You Size an Orifice Plate?

Sizing an orifice plate means choosing a bore that gives a measurable pressure difference at your flow range. The key number is the beta ratio, which is bore diameter divided by pipe diameter (d/D).

  • Beta range: standard plates are sized from 0.1 to 0.75, per Emerson.
  • Bore and thickness: the bore must be at least 12.5 mm, and plate thickness sits between 0.005D and 0.02D, as Kobold summarizes from ISO 5167-2.
  • The trade-off: a small beta gives a strong signal but more pressure loss and edge wear, notes Fabrico.
  • Real-world thickness: One maker uses 1/8-inch plates up to 14-inch pipe and 1/4-inch for 16-inch and larger. High pressure differences may need a thicker plate to prevent deflection.
  • Scope: ISO 5167-2:2022 covers pipes from 50 mm to 1,000 mm and pipe Reynolds numbers of 5,000 or more.

What Data Does the Maker Need?

The more you share, the less the maker has to guess. Send these with your inquiry:

  • Fluid name and state (gas, liquid, steam)
  • Minimum, normal, and maximum flow
  • Operating pressure and temperature
  • Pipe inside diameter and schedule
  • Allowed pressure loss
  • Preferred tapping style

Which Orifice Plate Material Should You Pick?

Start with 316 or 316L stainless steel, and switch only when the fluid demands it. The wrong metal is an expensive lesson.

  • Stainless steel 316/316L: listed as the standard material on WIKA’s datasheet. Some makers list 304 as their standard.
  • Monel 400: one maker uses Monel for oxygen service plates.
  • Hastelloy C276, duplex, and super duplex: offered by makers for tougher media.
  • Flanges and fittings: match them to the line material, and ask for material test certificates with the plate.

Which Standards Apply to an Orifice Plate?

Orifice plates are usually specified to one of three standards: ISO 5167, ASME MFC-3M, or AGA Report No. 3, says Emerson. Pick one and name it on the datasheet.

  • ISO 5167-2:2022: the main international reference. A standards listing shows India’s IS 14615 Part 2:2025 as identical.
  • API MPMS 14.3 (AGA Report No. 3): the usual choice for natural gas custody transfer.
  • ASME MFC-14M: covers small-bore orifice meters from 1/4 inch to 1.5 inch, per one maker’s catalogue.

A straight run depends on the beta ratio and the upstream fitting. Emerson’s table lists 16 pipe diameters after a single 90-degree bend at a beta of 0.4 under all three standards.

Orifice Plate vs Venturi: When Should You Switch?

Switch when pressure loss or flow range matters more than cost. Choosing between an orifice and a venturi meter is mostly a budget versus energy question.

  • Orifice: lower cost, turndown of 3:1 to 5:1, and permanent pressure loss near two-thirds of the pressure difference (Automation.com).
  • Venturi: turns down to 10:1 and has much lower pressure loss but a higher price (EngineerExcel).

What Should EHS and EPC Teams Check Before Ordering an Orifice Plate?

Check the standard, sizing sheet, material, and paperwork before you compare prices. A cheap plate with no paperwork is a risk, not a saving.

  • Standard named on the orifice plate datasheet.
  • Sizing sheet with beta ratio, pressure difference, and pressure loss.
  • Material test certificates for the plate and flange.
  • Edge inspection report, since even slight erosion can hurt accuracy (Automation.com)
  • Pressure rating and tapping style that match the flange.
  • Transmitter range that matches the sizing sheet.
  • Inspection plan: one industry guide suggests verification about every 5 years in clean service and every 1 to 2 years in erosive service.

Optional read: if leak safety is also on your plate, see this guide on how to choose an infrared gas detector for methane, propane, and LPG leaks.

FAQs

1. What is an orifice plate used for in flow measurement?
It creates a pressure drop in a pipe so you can calculate the flow of liquids, gases, and steam.

2. What is the orifice plate working principle?
Fluid speeds up through the hole, pressure drops, and that drop tells you the flow rate.

3. What is the standard beta ratio range for an orifice plate?
Standard plates are sized from 0.1 to 0.75.

4. Which material is best for an orifice plate?
316 or 316L stainless steel is the usual standard, with alloys like Monel or Hastelloy for harsh fluids.

5. What are the types of orifice plates?
Common types are square-edge, quarter-circle, conical entrance, eccentric, and segmental.

6. Which standards cover an orifice plate?
ISO 5167-2, ASME MFC-3M, and AGA Report No. 3 (API MPMS 14.3) are the main ones.

Ready to Spec Yours?

Send your fluid, pipe size, pressure, and temperature to the team at pcd-flowmeter.com and get help choosing the right orifice plate for your line.

 

Tags:Flow Meter